How can importers establish a your suppliers in China.standard, and then enforce it? Here are 4 proven ways to handle
1. Insist on getting a “perfect” sample
Whenever possible, you should have a perfect sample (i.e. a prototype that is conform in all points to what you want to receive) in your hands before production is launched. The best practice is to get at least two samples, and send one back to the factory with your signature/stamp on it.
This is the most basic way to establish your quality standard. The difficulty will be in the enforcement.
In China, in General, factories know that sending very nice samples is what helps them get orders. These perfect samples (prepared by experimented technicians who take their time) are usually better than what can be made in mass production.
Suppliers simply assume that the buyers know it. And in any case, a buyer who has wired a 30% deposit and is in a hurry to ship usually accepts this situation. Many factories count on it.
How not to fall in that trap?
1. You should avoid at all cost to settle the payment before the quality of bulk production is approved (either by yourself of by an inspection company).
2. You should write a note about what has to be EXACTLY similar to the perfect sample (e.g. the overall outlook, the color, the function, etc.) and get your supplier to sign it.
3. You should make a list of the differences that you can live with (see next part).
4. Check early in the production cycle. If you can afford it, send either one of your technicians or a third-party inspector in the factory. When? During production, as soon as finished products get off the lines.
This way, you will notice if the factory is not respecting your quality standard. And you will have time to negotiate a solution with your supplier.
If possible, the factory can avoid the same problems on the products that are not in the process yet. And they can rework (or reproduce) the output that you have rejected.
2. Define tolerances wherever applicable
Sometimes it is not realistic to expect a very precise result. For example, garments are generally made by hand, so there has to be a tolerance for measurements (example: 15cm in S size, +/-1cm). In this case, the objective is the comfort of the garment.
Another example: for juvenile products (toys, children clothes…), it should be impossible to pull small accessories off with a force of 90 Newton of less. If you have no idea about the safety issues surrounding your products, you can get in touch with a quality control firm.
Once you have approved some tolerances, put all your specifications on paper and get your supplier’s signature on them. You have already done half the work to establish and enforce a relevant quality standard.
These specifications will naturally become the inspection checklist when time comes to verify quality.
Sometimes it makes no sense to give a tolerance, of course. Here are two examples: “hard disk drive should be 120 GB in capacity”; “red color is Pantone 1664”. In these cases, your specification is clear and precise, and the supplier should follow it.
3. Set a limit on the proportion of defects
A defect is an issue that you cannot accept on all products.
In the aeronautics industry, manufacturers have to guarantee near-defect-free products. But for consumer goods such as toys or apparel, such a high quality standard is neither realistic not necessary.
The different types of defects
Some defects are worse than others:
Critical defects might hurt the user;
Major defects are not acceptable by most buyers in stores (e.g. large stains) or might cause problems in the supply chain (e.g. unreadable carton barcodes);
Minor defects can be tolerated by most buyers, but only in small quantity.
How to set a limit on the proportion of defects?
The quality control industry uses the same statistics (derived from a US army standard), when it comes to checking consumer goods.
All inspectors, and virtually all factories and traders, are familiar with the contact of AQL (Acceptance Quality Limits). In clear, the AQL is the highest proportion of defects that you can accept.
For most product categories, the AQL limits are usually the following:
0% for critical defects
2.5% for major defects (or 1.5% for relatively valuable goods)
4.0% for minor defects (or 2.5% for relatively valuable goods)
As a buyer, you have total freedom in setting these limits. But you are advised to discuss this from the beginning with your supplier, and to get their written agreement.
4. A quality standard suffers no exception
Let’s say a supplier is late, you negotiate a delay with your customers, and before shipment you notice that quality is less than desirable. You still prefer delivering the products, rather than cancelling the order. So you tell your supplier that he can ship out and next time should be better.
The problem is, the “exceptional tolerance” may become a “hint” for the factory. Count on them to remember that you can accept less-than-perfect products.
Chinese manufacturers tend to have a “can’t do” attitude after an order production has started. Two of their favorite expressions are “cha bu duo” (it’s off, but not by much, so you should accept it as is) and “mei ban fa” (there is nothing we can do about it now, no need to keep pressing this issue).
You should fight their natural inclination. Ask for re-work and re-inspections, even if it costs you 10 days. This type of efforts pay off handsomely in the long term, as long as the factory can reasonable achieve your quality standard (you will have clarified this if you follow the steps I listed above).
If in very special case you have to deliver the products, you must talk with factory people in very serious manner, so they understand you do not accept any repeated problems, if it happens again, you will leave this factory.